Peralatan kantong cair untuk tas tipe penyegelan miring

Basic parameters of the slanted type sealing at both sides of bags packing machine:

Capacity(bag/min): 1020 pcs per min
Range of measurement(ml): 200-2000g sauce sachet
Bag size(mm): (L)50-350 , (W)50-200
Power(W): 1100
Source voltage: 380V/50Hz 220V/50~60Hz
Packing material: PET/PE,PET/AL foil/PE,PET/PE,NYLON/PE, etc.
Net weight(kg): 600kg
Overall dimensions: 625*1200*2250mm(L*W*H)

Keterangan

Sauce Paste Automatic Filling Packaging Machine Unit is specially set up for package of product with medium to high viscosity, such as tomato sauce, honey, soya sauce, tomato paste, marinara sauce, liquid waterproof coating, washing detergent, cooking oil, jam, ketchup, butter, peanut paste, sala sauce, chili sauce, mayonnaise, hand soap, semi-fluid products,

The machine can make pillow type bags, the metering range is 20-500g and 200-1000g, the maximum speed can reach 25bags/min.

Basic parameters of the slanted type sealing at both sides of bags packing machine:

Capacity(bag/min): 10-25 pcs per min
Range of measurement(ml): 200-2000g sauce sachet
Bag size(mm): (L)50-350 , (W)50-200
Power(W): 1100
Source voltage: 380V/50Hz 220V/50~60Hz
Packing material :PET/PE,PET/AL foil/PE,PET/PE,NYLON/PE, etc.
Net weight(kg): 600kg
Overall dimensions: 625*1200*2250mm(L*W*H)

Machine Configuration:

Item Type of brand
PLC: Mitsubish(Japan)
Mitsubish(Japan) Xinjie(China)
Photoelectric tester: Longyou(China)

Motor Motor
Air cylinder AirTAC
Material Material contact part--304 Stainless Steel / bodyshell-201 stainless steel.

Mesin terintegrasi dengan tangki pencampur dan sambungan pipa terkait

Karakteristik teknis dari mesin pengemas cair lotion krim gel rambut:

1． Tampilan layar bahasa Inggris dan Cina, pengoperasiannya sederhana.
2 Sistem komputer PLC, fungsinya lebih stabil, penyesuaian parameter apa pun tidak perlu menghentikan mesin.
3 Itu dapat menyimpan sepuluh buang, mudah untuk mengubah variasi.
4． Putuskan film gambar motor, posisikan secara akurat.
5． Sistem kontrol independen suhu, presisi sampai ± 1 .
6 Horizontal, kontrol suhu vertikal, cocok untuk berbagai film campuran, bahan kemasan film PE.
7 Diversifikasi jenis pengepakan, penyegelan bantal, tipe berdiri, meninju dll.
8． Bag–making , sealing, packing, print date in one operation.Work circumstance quiet, low noise.
9. Air expelled before bagging;

Fished bags samples

Common faults, reasons and elimination

Masalah	Reason	Shooting way
Touch the key of ON, but the machine does not work	1.check if emergency stop switch is restored2.transducer and servo controller display RC	1.restore emergency stop switch 2.turn off main power supply, turn it on after 20 seconds creep-age switch trips
creepage switch trips	creepage of heating sheet and other electrical appliances	check electric appliances one by one, eliminate
sealing roll not hot	1.protector of open circuit trips 2.heating sheet burnt out 3.temperature control meter damaged	1.check and eliminate open circuit, recover it 2.replace heating sheet 3.replace temperature control meter
Number on temperature control meter bounces repeatedly	Thermcouple loose or damaged	Fix or replace thermocouple
temperature is normal when close down, but descends continuously when running	1.environmental voltage is low, causing descending of power of heating sheet 2.power of heating sheet is too low	1.reduce packing speed or add voltage stabilizing device 2.replace it with heating sheet of bigger power
air leak at sealed mouth of packing bag	1.temperature is insufficient 2.pressure is insufficient 3.sealing time is too short 4.irregular front and back horizontal sealing rolls 5.material clamped	1.properly increase temperature 2.check if total pressure is 6.5 kilograms 3.properly increase sealing time parameter 4.carefully adjust parallel status of mouth of horizontal sealing roll 5.adjust baiting time or inflation delay
cutting position or cut into half a bag can not be controlled	1.side of packaging film cockles or photoelectric wrong action caused by poor quality of light path 2.sensitivity of photoelectric head isn’t adjusted well 3.bag set length is insufficient and different lengths caused	1.replace packing film2.re-adjust photoelectric sensitivity 3.increase bag length
conveyance film does not drop	1.pressure of conveyance film cylinder is insufficient or too much 2.belt slides of damaged 3.static of packing film is too big	1.check if pressure of conveyance film is 2.5 kilograms 2.scrape surface of belt with saw sheet or replace it 3.replace packing film